橡胶接头「测试站不选词,只靠文章页获取流量」-「董帝豪SEO」

安装说明VIEWS

橡胶接头「测试站不选词,只靠文章页获取流量」-「董帝豪SEO」

「专业」橡胶接头解剖图、生产工艺和生产硫化工艺

来源:「专业」橡胶接头解剖图、生产工艺和生产硫化工艺 发布于:2019-06-30 02:24   浏览:

橡胶接头在制作的过程中,内部并不是纯橡胶,而是带有锦纶帘子布和编织网的。制作合格的橡胶接头是将内胶层管坯放置于工作台,管芯表面涂上适量的隔离剂,然后内胶层管坯充入适量的空气进行套芯。套芯后,整理、检查、整径并存放好,送下一工序进行缠绕成型。 根据施工表的要求,确定缠绕设备的分线片、口型、缠绕行程。缠绕一根钢丝橡胶接头前,将钢丝按出线方向经引线环、张力装詈、分线片、整形口型,然后用胶布按缠绕方向紧扎在牵引机上的引管上,开动缠绕机,使引管缓慢前进,通过调速器,调整牵引速度,使缠绕行程达到要求。
In the manufacturing process of rubber joint, the interior is not pure rubber, but with nylon cord fabric and woven mesh. The qualified rubber joint is made by placing the inner rubber tube blank on the worktable, coating the surface of the tube core with a suitable amount of isolating agent, and then filling the inner rubber tube blank with appropriate amount of air for coring. After core bushing, the core is arranged, inspected, the whole diameter is stored and sent to the next process for winding forming. According to the requirements of the construction table, the dividing piece, the profile and the winding stroke of the winding equipment are determined. Before winding a steel wire rubber joint, the steel wire is tied to the lead pipe of the tractor in the direction of winding direction through the lead ring, tension mounting, wire splitting piece and shaping orifice, then the winding machine is operated to make the lead pipe move slowly and adjust the traction speed through the speed regulator so as to make the winding stroke meet the requirements.

避震喉剖面图

橡胶接头原型缠绕行程调好后,将中胶片装上,并引进已编好保护层的管坯并且表面还要喷涂脱模剂,即可开始钢丝橡胶软接头缠绕。缠绕开始时,速度要逐渐递增,到达一定速度后缠绕,缠绕过程中应将中胶片同时平服地引入缠绕层。缠绕时,钢丝张力要均匀,钢丝在管坯上应顺序排列,均匀平整,牵引装置压管要适度,不宜过紧,防止管坯变形。
After the winding stroke of the rubber joint prototype is adjusted, the medium film is mounted, and the tube blank with the protective layer is introduced, and the surface is sprayed with demoulding agent, so that the winding of the steel wire rubber soft joint can begin. At the beginning of winding, the speed should increase gradually, and after reaching a certain speed, the medium film should be introduced into the winding layer at the same time in the winding process. When winding, the tension of the steel wire should be uniform, the steel wire should be arranged in sequence on the billet, uniform and flat, and the pipe pressing of the traction device should be moderate, not too tight, so as to prevent the deformation of the billet.


上海淞江减震器集团有限公司为技术部为大家分享一些上海淞江橡胶接头生产工艺和生产硫化工艺等知识,方便大家学习和了解上海淞江橡胶接头产品,提高大家的专业知识!以下这张照片是上海淞江减震器集团有限公司网络部在我厂上海淞江橡胶接头硫化车间拍的,请勿转载,谢谢合作!
Shanghai Songjiang Shock Absorber Group Co., Ltd. shares some knowledge about the production process and vulcanization process of Shanghai Songjiang Rubber Joint for the technical department. It is convenient for you to learn and understand the products of Shanghai Songjiang Rubber Joint and improve your professional knowledge.

上海淞江橡胶接头磨具外壳,主要是用于硫化上海淞江橡胶接头使用!
Shanghai Songjiang Rubber Joint Abrasive Shell is mainly used for vulcanizing Shanghai Songjiang Rubber Joint.

上海避震喉生产工艺,淞江避震喉生产工艺

上海淞江橡胶接头硫化机器,中间放的那个橡胶是所谓的气胆磨具,就是真正的气吹膜工艺,没有气胆的完全不是气吹膜工艺,请勿被忽悠了!

Shanghai Songjiang Rubber Joint Vulcanization Machine, the rubber placed in the middle is the so-called gas-gall abrasives, which is the real gas-blown film process, no gas-gall is not the gas-blown film process, please don't be fooled!

上海避震喉生产工艺,淞江避震喉生产工艺

下面由上海淞江减震器集团技术部为大家介绍一下上海淞江橡胶接头生产工艺和硫化工艺:
1、从原材料开始严格把关,每批原材料经化验员检验合格后进厂,有专业的橡胶配料人员按要求比例配料。
2、配料完成后送进橡胶混炼车间,经橡胶混炼机压炼为合成橡胶片。
3、合成橡胶片经检验合格后送进橡胶接头下料车间,工作人员按照不同型号尺寸下料。
4、下料完成后进行成型。
5、每个橡胶接头胎型经检验合格后送进硫化车间,工作人员将胎型放入模具。
6、将模具放进硫化机,硫化机将模具压好,此时硫化机调好温度恒温180度,进行40分钟的硫化。
7、40分钟后将硫化完成的橡胶接头从模具中取出,检测橡胶接头的硫化完整度。
8、将硫化完成的橡胶接头修边,修边完成后放入半成品缆车。
9、将缆车里面的橡胶接头半成品送进法兰组装车间,工作人员将橡胶接头法兰和橡胶接头半成品组装为成品。
10、质检部人员将橡胶接头成品进行随机抽样试压,试压合格的橡胶接头进行包装。
11、包装好的橡胶接头成品放入仓库,等待装车发货。

Following is the introduction of the production process and vulcanization process of Shanghai Songjiang Rubber Joint by the Technical Department of Shanghai Songjiang Shock Absorber Group.
1. Starting from the strict control of raw materials, each batch of raw materials is qualified by the laboratory inspectors before entering the factory. Professional rubber ingredient personnel are required to proportionate ingredients.
2. After the batching is finished, it is sent to the rubber mixing workshop and pressed into synthetic rubber sheet by the rubber mixer.
3. The synthetic rubber sheet is sent to the blanking workshop of rubber joint after passing the inspection, and the staff will blank according to different sizes.
4. Shaping after blanking.
5. After passing the test, the tire of each rubber joint is sent to the vulcanization workshop, and the worker puts the tire into the mould.
6. Put the mould into the curing machine, and the curing machine press the mould well. At this time, the curing machine adjusts the temperature to 180 degrees and cures for 40 minutes.
After 7 and 40 minutes, the vulcanized rubber joints were removed from the mould and the vulcanization integrity of the rubber joints was tested.
8. Rubber joint trimmed after vulcanization and put into semi-finished cable car after trimming.
9. The semi-finished rubber joints inside the cable car are sent to the flange assembly workshop, and the workers assemble the semi-finished rubber joints flanges and rubber joints into finished products.
10. The personnel of Quality Inspection Department will sample the finished rubber joints randomly and pack the qualified rubber joints.
11. The finished products of the packaged rubber joints are put into the warehouse, waiting for loading and delivery.
 
以上就是上海淞江橡胶接头的生产硫化工艺,我厂层层把关,严格按照要求生产,达到要求,避免工程问题出现。只有你选择正规厂家的产品,才能对你的工程有所保障,质量稳定可靠的产品是由严格的把控出来的,而不是小型作坊模仿出来的,欢迎新老客户到我厂实地参观考察,可以对比其他工厂产品,这样你就会知道什么是正规厂家的产品了!
The above is the vulcanization process of Shanghai Songjiang Rubber Joints. Our factory keeps checks on all levels, produces strictly according to the requirements, meets the requirements, and avoids engineering problems. Only when you choose the products from the regular manufacturers can you guarantee your project. The products with stable and reliable quality are controlled strictly, not imitated by small workshops. Welcome new and old customers to visit our factory on the spot. You can compare the products from other factories. Then you will know what the regular manufacturers are. Product!
 
 
 

本文作者:董帝豪

本文地址:https://www.chinadihao.com/269.html

本文来源:上海淞江减震器集团有限公司

注意事项:专业型问题以淞江集团技术部解释为准,网编主要目的是为大家提供一个流量入口。

本文著作权归上海淞江集团所有,任何形式的转载都请联系作者获得授权并注明出处。


推荐产品








最新推荐:
·「苏州询价」液压油DN100橡胶接头,上海淞江,压力1.6 ·「南京询价」山东石岛湾核电站准备采购橡胶接头
·「2019」国内乃至全球橡胶接头行业中,单次配套导流筒 ·「2019」三元乙丙橡胶接头采用中石化三井公司的EPDM 4
·「丽水询价」DN32/40/50橡胶接头,法兰不锈钢304,PN16 ·「苏州询价」纯水处理配套同心软接:DN100-6台,DN65-
·「上海询价」可曲挠橡胶接头KXT2.5*200,常温,推荐天 ·「2019」温州客户定的防拉脱限位装置橡胶接头发货现场
·「昆明询价」DN700 PN1.6的耐酸碱橡胶软连接,长度大 ·「姜堰询价」法兰热镀锌,橡胶为EPDM,耐腐蚀,含限位